According to a recent press released from the State Administration for Market Regulation ("SAMR") and the Standardization Administration of the People's Republic of China (SAC), 454 New GB Standards ("GB", "GuoBiao") were approved on 17 September 2018 and will be released, e.g. automobile wheel safety performance requirements and test methods, indoor fire hydrant, etc.

If you have any questions, please use the Contact Us page. For general information on the China CCC please look through the chapter CCC procedure.

Source: SAMR News

According to a joint announcement by the SAMR ("State Administration for Market Regulation") and the CNCA ("Certification and Accreditation Administration of the PRC") on 15 June 2018, a new certification procedure "self-declaration" were firstly introduced in China and it comes into force on 1 October 2018. This new certification procedure is avaiable for a list of selected products that are within the scope of CCC Product category. Recently, a list of by CNCA accredited test labs were invited to test the new platform, which calls CCC Product Self Declaration Conformity Information Submission System (see here). Companies in China can register for this platform. The prerequisite condition for the registration is that the company must have a place of business and legal personality in China. Our team will continue to pay attention to the relevant information about the China CCC self declaration.

For general information on the CCC please look through the chapter CCC procedure. If you have any questions, please use the Contact Us page.

 

 

on 11 June 2018, a list of products were deleted from the ccc category, which means these products are no longer subject to China CCC Certification (see "CCC product category changed"). According to a recent accouncement released by the CNCA ("Certification and Accreditation Administration of the PRC"), for those non-ccc products, factory should stop using ccc mark. If it is not possible for some reasons, such as, the CCC mark is affixed by molding or printing on the product, factory can use ccc mark until natural transition e.g. through tools adaptation, inventory turnover of products or packaging, etc. If the factory affixes the standard CCC mark ("sticker") on the product, the CCC mark shall not be affixed from the date of invalidation of the CCC certificate.

If you have any questions, please use the Contact Us page. For general information on the China CCC please look through the chapter CCC procedure.

Source: CNCA No.35.2018

 

 

 

 

 

 

 

With the rapid development of China and Germany in the field of autonomous driving and intelligent networked vehicles, the cooperation between Chinese and German enterprises is also in full swing. Recently, Baidu, the domestic auto-driving giant, and Daimler, the German auto industry giant, announced that they will deepen strategic cooperation in the fields of autonomous driving and vehicle networking. In the future, the two sides will establish closer cooperation and promote the rapid development of the global autonomous driving industry. In early July 2018, Daimler became the first international automaker to receive a road test license for self-driving vehicles in Beijing. It is reported that the licensed Mercedes-Benz autopilot test vehicle is powered by the Baidu Apollo open platform. Autopilot technology. At present, these test vehicles have been extensively tested in the test site of Haidian District, Beijing. In the future, both parties will continue to add new test environments on the open roads of open testing and dedicated test sites to improve the complexity of the scene.

Motor vehicle and a list of vehicle components need a China CCC Certification in order to enter into the chinese market. If you have any questions, please use the Contact Us page. For general information on the China CCC please look through the chapter CCC procedure.

Source: CAAM News

 

According to a recent announcement by the CNCA ("Certification and Accreditation Administration of the PRC", "中国国家认证认可监督管理委员"), a new implementation rules for E-bike CNCA-C11-16: 2018 was released on 19 July 2018,and it comes into force on 1 August 2018. Here are the certification organisations CQC, CCAP, CCLC, QTCTC, SMQ which are responsibile for CCC Certification for E-bike. Hier is a list of test laboratories for testing E-bike.

you have any questions, please use the Contact Us page. For general information on the China CCC please look through the chapter CCC procedure.

Source: CNCA notice No.31.2018, No.32.2018

According to a recent press released from the Standardization Administration of the People's Republic of China (SAC),  160 New GB Standards ("GB", "GuoBiao", "国标") released on 13 July 2018. Here you can find a part of new GB Standards that are relevant to automotive products. 

GB/T 273.2-2018 Rolling bearings - Overall dimensions - Part 2: Thrust bearings
GB/T 7813-2018 Rolling bearings Split vertical housings Dimensions
GB 13895-2018 Heavy Duty Vehicle Gear Oil (GL-5)
GB/T 26949.16-2018 Industrial vehicles Stability verification Part 16: Walker vehicles
GB/T 26949.9-2018 Industrial vehicles - Stability verification - Part 9: Counterbalanced forklifts carrying cargo containers of 6 m or more length
GB/T 36507-2018 Industrial vehicles Safety regulations for use, operation and maintenance
GB/T 36516-2018 Iron chrome aluminum fiber filament for motor vehicle purification filter
GB/Z 36517-2018 Rolling bearings Calculation method for bearing correction reference rated life under general load conditions

New GB Standards in other field, please see here.

If you have any questions, please use the Contact Us page. For general information on the CCC please look through the chapter CCC procedure.

 

According to a recent press release from the Quality and Certification Plattform in China (cncete),  882 New GB Standards ("GB", "GuoBiao", "国标") came in to force on 01 July 2018. Here you can find a part of new GB Standards that are relevant to automotive products. 
 
GB/T 18487.2-2017 Conductive charging systems for electric vehicles - Part 2: Electromagnetic compatibility requirements for non-vehicle conductive power supply equipment (replaced GB/T 18487.2-2001)
GB/T 35175-2017 High-speed switch solenoid valve for automatic transmission
GB/T 35178-2017 Fuel cell electric vehicle Hydrogen consumption Measurement method
GB/T 35179-2017 Bench test method for safe driving performance of electric vehicles
GB/T 35260-2017 Technical Specifications for Bus Maintenance
GB/T 35349-2017 Automotive parking brake performance test method
GB/T 35358.1-2017 Automotive air compressors and compressors - Air conditioning systems - Part 1 : grading grading efficiency (0.3 um to 5 um)
GB/T 35358.2-2017 Automotive air-conditioners for compressors and compressors Part 2: Grading efficiency test for coarse granules (5μm to 40μm)
GB/T 35360-2017 Automotive Steering System Terms and Definitions
GB/T 35363-2017 Automobile engine diesel filter and fuel filter Determination of filtration efficiency and dirt holding capacity
GB/T 35369-2017 occupant detection device for vehicle seat belt reminder
GB/T 35751-2017 Non-woven fabrics and composite non-woven fabrics for automotive decoration
GB/T 35785-2017 Motor vehicle electronic marking read-write equipment installation specification
GB/T 35786-2017 General specification for reading and writing electronic equipment for motor vehicles
GB/T 35787-2017 Safety Technical Requirements for Motor Vehicles' Electronic Mark Reading and Writing Equipment
GB/T 35788-2017 Motor Vehicle Electronic Identification Safety Technical Requirements
GB/T 35789.1-2017 General specification for electronic identification of motor vehicles Part 1: Cars
GB/T 35790.1-2017 Code for the installation of motor vehicle electronic markings Part 1: Cars
GB/T 35347-2017 Motor Vehicle Safety Technology Inspection Station

New GB Standards in other field, e.g. Electronic Equipment, Textiles, Environmental Conditions, Electrical Machinery Safety, Chemical Fibers, Electrical Insulation Materials, Information Technology, Hydraulic Machinery, Navigation,etc., please see here.

For general information on the CCC please look through the chapter CCC procedure. If you have any questions, please use the Contact Us page.

 
According to a recent joint announcement by the SAMR ("State Administration for Market Regulation", "国家市场监督管理总局") and the CNCA ("Certification and Accreditation Administration of the PRC", "中国国家认证认可监督管理委员"), two new certification procedures are available from 1 October 2018 for the following products that are within the scope of CCC Product category, i.e.:
 
Certification Procedure A: self-selected laboratory type test + self-declaration
Certification Procedure B: Designated laboratory type test + self declaration
 
for more details please see here
 
 
Certification Procedure A: self-selected laboratory type test + self-declaration:
Product Implementation Regulation
Nominal rated voltage in information technology equipment, audio and video equipment equal to or less than 5VDC, nominal rated power consumption less than 15W (or 15VA), and no rechargeable battery equipment (Class III equipment)

CNCA-C08-01:2014 "Rules for Implementing Compulsory Product Certification Audio and Video Equipment"

CNCA-C09-01:2014 "Implementation Rules for Mandatory Product Certification Information Technology Equipment"

Certification Procedure B: Designated laboratory type test + self declaration:

Product Implementation Regulation
Low-voltage switchgear: complete power switchgear, bus trunk system (busway), distribution board, low-voltage reactive power compensation device CNCA-C03-01:2014 "Mandatory Product Certification Implementation Rules Low Voltage Switchgear"
Small-power motor CNCA-C04-01:2014 “Rules for implementation of compulsory product certification”
Small AC arc welding machine
AC arc welding machine
DC arc welding machine
TIG arc welding machine
MIG/MAG arc welding machine
Submerged arc welding machine
Plasma arc cutting machine
Plasma arc welding machine
Arc welding transformer anti-electric shock device
Welding cable coupling device
Resistance welding machine
Wire feeding device
TIG welding torch
MIG/MAG welding torch
Electrode holder
CNCA-C06-01:2014 “Rules for Implementation of Mandatory Product Certification Welding Machine”
Motor – Compressor CNCA-C07-01:2017 “Mandatory Product Certification Implementation Rules for Household and Similar Use Equipment”
Automotive interior parts CNCA-C11-09:2014 “Mandatory Product Certification Implementation Rules for Automotive Interior Parts”
Automotive door locks and door retainers CNCA-C11-10:2014 "Implementation Rules for Compulsory Product Certification Car Door Locks and Door Holders"

For general information on the CCC please look through the chapter CCC procedure. If you have any questions, please use the Contact Us page.

Support

Unterstützung

You work at your pace. You can handle your projects independently via our portal, as well as inquire about personal support. We have therefore committed ourselves to give you the opportunity to design your own processes, without having to give up the support through our portal through us

Online Administration

Online Verwaltung

We offer you the opportunity to carry out your certification processes yourself, but without having to forego the know-how or the support of experienced employees. The online system is designed for a variety of certifications and offers you also FAQ lists, as well as ready-made forms and tables, as well as a module to clarify open questions with one of our employees.

Change Certification

Change Certification

In our fast time changes in business life are a constant accompaniment. Fixed structures that used to build up over many years can now be smashed very quickly. There are internal and external reasons for this. The CS gives an overview of the conformity during changes.

Cooperation

Kooperationen

Since we all only have a limited time and financial capacity, and want to offer the customer a comprehensive service, cooperations only make sense among related organizations. These have a reliable structure, as well as a good interpersonal harmony.

Go to top