With the rapid development of China and Germany in the field of autonomous driving and intelligent networked vehicles, the cooperation between Chinese and German enterprises is also in full swing. Recently, Baidu, the domestic auto-driving giant, and Daimler, the German auto industry giant, announced that they will deepen strategic cooperation in the fields of autonomous driving and vehicle networking. In the future, the two sides will establish closer cooperation and promote the rapid development of the global autonomous driving industry. In early July 2018, Daimler became the first international automaker to receive a road test license for self-driving vehicles in Beijing. It is reported that the licensed Mercedes-Benz autopilot test vehicle is powered by the Baidu Apollo open platform. Autopilot technology. At present, these test vehicles have been extensively tested in the test site of Haidian District, Beijing. In the future, both parties will continue to add new test environments on the open roads of open testing and dedicated test sites to improve the complexity of the scene.
Motor vehicle and a list of vehicle components need a China CCC Certification in order to enter into the chinese market. If you have any questions, please use the Contact Us page. For general information on the China CCC please look through the chapter CCC procedure.
Source: CAAM News
According to a recent announcement by the CNCA ("Certification and Accreditation Administration of the PRC", "中国国家认证认可监督管理委员"), a new implementation rules for E-bike CNCA-C11-16: 2018 was released on 19 July 2018,and it comes into force on 1 August 2018. Here are the certification organisations CQC, CCAP, CCLC, QTCTC, SMQ which are responsibile for CCC Certification for E-bike. Hier is a list of test laboratories for testing E-bike.
According to a recent press released from the Standardization Administration of the People's Republic of China (SAC), 160 New GB Standards ("GB", "GuoBiao", "国标") released on 13 July 2018. Here you can find a part of new GB Standards that are relevant to automotive products.
New GB Standards in other field, please see here.
|GB/T 18487.2-2017 Conductive charging systems for electric vehicles - Part 2: Electromagnetic compatibility requirements for non-vehicle conductive power supply equipment (replaced GB/T 18487.2-2001)|
|GB/T 35175-2017 High-speed switch solenoid valve for automatic transmission|
|GB/T 35178-2017 Fuel cell electric vehicle Hydrogen consumption Measurement method|
|GB/T 35179-2017 Bench test method for safe driving performance of electric vehicles|
|GB/T 35260-2017 Technical Specifications for Bus Maintenance|
|GB/T 35349-2017 Automotive parking brake performance test method|
|GB/T 35358.1-2017 Automotive air compressors and compressors - Air conditioning systems - Part 1 : grading grading efficiency (0.3 um to 5 um)|
|GB/T 35358.2-2017 Automotive air-conditioners for compressors and compressors Part 2: Grading efficiency test for coarse granules (5μm to 40μm)|
|GB/T 35360-2017 Automotive Steering System Terms and Definitions|
|GB/T 35363-2017 Automobile engine diesel filter and fuel filter Determination of filtration efficiency and dirt holding capacity|
|GB/T 35369-2017 occupant detection device for vehicle seat belt reminder|
|GB/T 35751-2017 Non-woven fabrics and composite non-woven fabrics for automotive decoration|
|GB/T 35785-2017 Motor vehicle electronic marking read-write equipment installation specification|
|GB/T 35786-2017 General specification for reading and writing electronic equipment for motor vehicles|
|GB/T 35787-2017 Safety Technical Requirements for Motor Vehicles' Electronic Mark Reading and Writing Equipment|
|GB/T 35788-2017 Motor Vehicle Electronic Identification Safety Technical Requirements|
|GB/T 35789.1-2017 General specification for electronic identification of motor vehicles Part 1: Cars|
|GB/T 35790.1-2017 Code for the installation of motor vehicle electronic markings Part 1: Cars|
GB/T 35347-2017 Motor Vehicle Safety Technology Inspection Station
New GB Standards in other field, e.g. Electronic Equipment, Textiles, Environmental Conditions, Electrical Machinery Safety, Chemical Fibers, Electrical Insulation Materials, Information Technology, Hydraulic Machinery, Navigation，etc., please see here.
|Nominal rated voltage in information technology equipment, audio and video equipment equal to or less than 5VDC, nominal rated power consumption less than 15W (or 15VA), and no rechargeable battery equipment (Class III equipment)||
CNCA-C08-01:2014 "Rules for Implementing Compulsory Product Certification Audio and Video Equipment"
CNCA-C09-01:2014 "Implementation Rules for Mandatory Product Certification Information Technology Equipment"
Certification Procedure B: Designated laboratory type test + self declaration:
|Low-voltage switchgear: complete power switchgear, bus trunk system (busway), distribution board, low-voltage reactive power compensation device||CNCA-C03-01:2014 "Mandatory Product Certification Implementation Rules Low Voltage Switchgear"|
|Small-power motor||CNCA-C04-01:2014 “Rules for implementation of compulsory product certification”|
Small AC arc welding machine
AC arc welding machine
DC arc welding machine
TIG arc welding machine
MIG/MAG arc welding machine
Submerged arc welding machine
Plasma arc cutting machine
Plasma arc welding machine
Arc welding transformer anti-electric shock device
Welding cable coupling device
Resistance welding machine
Wire feeding device
TIG welding torch
MIG/MAG welding torch
|CNCA-C06-01:2014 “Rules for Implementation of Mandatory Product Certification Welding Machine”|
|Motor – Compressor||CNCA-C07-01:2017 “Mandatory Product Certification Implementation Rules for Household and Similar Use Equipment”|
|Automotive interior parts||CNCA-C11-09:2014 “Mandatory Product Certification Implementation Rules for Automotive Interior Parts”|
|Automotive door locks and door retainers||CNCA-C11-10:2014 "Implementation Rules for Compulsory Product Certification Car Door Locks and Door Holders"|
According to a recent press released by the China National Light Industry Council, the light industry will focus its efforts on safety standards and accelerate the preparation and revision of a number of mandatory national standards ("GB Standard","国标") in the fields of home appliances, lighting, children's products, and toys to provide more protection for consumer safety. In these fields, they have accelerated the development of international standards comparisons and conversions, and strive to achieve 95% compliance with international standards by the end of 2018.
Home appliances, lighting, children's products, and toys are ccc relevant. For general information on the CCC please look through the chapter CCC procedure. If you have any questions, please use the Contact Us page.
(source: CNLIC News)
According to a recent press release by CCAA ("China Certification & Accreditation Association", "中国 认证 认可 协会"), 16's audit permissions have been revoked by Chinese auditors. It was found that the auditors had been unlawful either at registration or during the audit against the "Management System Auditor Registration Regulation", eg cheating of diplomas and work experience, failure to keep the audit plan, money under the table, as well as external auditors at the same time work as a Consultant or Legal Entity of a consulting firm, etc.